Brodit - Insmat

Brodit Galaxy Tab A9+ holder with lock&cig-plug

This holder is to be used when you will secure your device and still have it easy accessable. Perfect for use in stores, at exhibitions and any place where you want to use your device without having it easy removable. In order to remove the tablet from the holder you need the key or a certain amount of violence is required. The holder includes a lock and two keys. With USB-C cable with cig-plug adapter, choose to connect either to the vehicle's USB-C outlet or the 12/24V socket. The cig-plug adapter has two USB ports: Type-A and Type-C. You have full access to the camera and all buttons when the device is in the holder. It is easy to slide the device into place in the holder so it connects to the charging, and to take it out of the holder when leaving the car. The holder is equipped with a tilt swivel so you can easily adjust the angle for better viewing, or switch between portrait and landscape mode. Tilts 17° and swivels 360°. Mounting plate 42x50 mm with 4 mm AMPS-holes. Made of high grade black ABS/Acetal plastic. Made in Sweden. Attach onto a ProClip mounting platform. An installation of a tablet onto a vehicle’s dashboard is always done on the customer’s own responsibility. Brodit recommends to use tablets on a Pedestal mount or a Brodit headrest mount. Charging specifications - Output Connector Type: Dual USB, Type-A and Type-C Female. - Output Voltage: 5V, 9V, 12V(Nominal) - Output Current: - USB Port 1: TYPE-C PD: 3.6V ~ 6V/3A 6.2-9V/2A 9.2-12V/1.5A(Under full Load). - USB Port 2: TYPE-A, QC3.0. 3.6V ~ 6V/3A 6.2-9V/2A 9.2-12V/1.5A(Under full Load). - Output Voltage Ripple: 300mV pk-pk at Max Load - Input Voltage Range: DC 12--24V DC, Input can handle 40V Load dump translent events - Input Current: 3.0 A DC Max - Input Current with No device attached: 0.005A - DC-DC Conversion Efficiency: Over 86% Typical - Rated Power: - USB Port 1: TYPE-C 18Watts Max - USB Port 2: TYPE-A 18Watts Max

Hinta (alv) 165,23 €

Brodit Galaxy Tab Active 3/5 Holder for fixed...

Use an active holder for your Galaxy Tab Active 3/5 while driving and you will always have a freshly charged battery! The active holder is to be connected inside the dashboard. It provides a discreet and neat installation without any cables hanging over the interior. Safe and convenient! 12/24 Volt. The product is E-approved. Connect the power cable with a 2A fuse. 2,7A charger. Charging via pogo plug. Professional installation recommended. The holder is equipped with a tilt swivel so you can easily adjust the angle for better viewing. Tilts 17° and swivels 360°. Mounting plate 42x50 mm with 4 mm AMPS-holes. Made of high grade black ABS/Acetal plastic. Made in Sweden. Easy-switching system: The easy-switching system enables you to upgrade the holder only, and keep the installed cables. It saves you a lot of time! When upgrading to a new device, you do not longer need to make a full installation. Same goes for maintenance in case of warranty or damage. You simply disconnect the holder from the charging cable via the Molex 6-pin quick connector, and then connect the new holder. The switch is done in a few seconds. Tablets (Surfpads) should not be installed onto a car’s dashboard if they block the view or block key controls. ProClip (Brodit’s vehicle mounting bracket) is designed for installation of smaller devices like mobile phones and GPS devices, ProClip is not designed for large devices like tablets. In some vehicles the ProClip has an extra firm fit and can then be used also for installation of a tablet. If you want to place a tablet onto the car’s dashboard, each combination of tablet-car must be examined in detail by you in order to determine if such an installation is possible in the specific case. Consideration should be given to the position and how firmly the ProClip is in place, as well as the size of the tablet you wish to use. Brodit will not give any recommendations for such installations.

Hinta (alv) 120,44 €